git mv *.hint -> README.md

There is one exception:

    $ find . -name '*.hint' -execdir git mv '{}' README.md \;
    git statufatal: destination exists, source=1992/albert/albert.hint, destination=1992/albert/README.md

Looking at the two files they differ quite a bit so I've not changed it.
I'll bring this up on GitHub.

1992/westley/README.md

@@ -0,0 +1,112 @@
+Best Small Program:
+
+	Brian Westley (aka Merlyn LeRoy)
+	Digi International
+	1026 Blair Ave.
+	St. Paul, MN  55104
+	USA
+
+
+Judges' comments:
+
+    If lost:
+	make whereami
+    
+    Then run:
+	whereami lat long
+    
+    Where lat and long correspond to your latitude and longitude.
+
+    To find the approximate place where this entry was judged, type:
+
+	whereami 37 -122	(- means west of meridian)
+    
+
+Selected notes from the author:
+
+    Run the program with your latitude & longitude as integer
+    arguments; it will produce a map made up of '!' with the given
+    position marked with either a '"' (if the position is over a '!')
+    or a '#' (if the position is over a space).  Southern latitudes
+    and western longitudes are entered as negative numbers.  For
+    example, to find San Francisco, run with "prog 38 -122".  The
+    resolution of the map is five degrees horizontally, ten degrees
+    vertically.  The map is a Mercator projection with equal spacing
+    of the latitudes, so the areas near the poles are very distorted.
+    Latitudes near the poles and Antarctica are not shown.
+
+    The program requires the ASCII character set, putchar(), atoi(),
+    and a display that auto-wraps at 80 characters(!).  If your display
+    does not work this way, you will have to massage the output;
+    for example, you can pipe it to a file and edit it with vi,
+    which will do autowrap for you.
+
+    Lint complains that main() returns a random value and I'm not
+    checking the value that putchar() returns.  Scandalous!
+
+    If you run it with fewer than 2 arguments, it will likely
+    give you an exception, as it will access arguments that
+    don't exist and characters before a string constant.
+
+    How it works:
+
+    The map is printed as one long string of ' ' and '!' characters,
+    with the autowrap used to stack up slices of 80.  The map data is
+    a string; the first character is how many '!'s are printed
+    ('A'=1, 'B'=2, etc), the second character is how many ' 's, the
+    third is how many '!'s, etc.  ASCII characters less than 'A'
+    print no characters but still change the polarity, so any map
+    of ' 's and '!'s is possible.  This is done in the putchar()
+    argument as "33^l&1", where l is the character position+4; if
+    l is odd, ' ' is printed, if l is even, '!' is printed.
+
+    The position of latitude & longitude is changed into a single
+    character position within the one long string via the first
+    expression "d = latitude/10*80 - longitude/5 - offset"  The
+    latitude is divided by ten because the vertical resolution is
+    ten degrees, then multiplied by 80 because of the 80 character
+    wrap (i.e. each ten degrees moves the position up or down one
+    entire row).  The longitude is divided by five and added, because
+    five degrees of change moves the location one character.  The signs
+    are opposite because latitude is decreasing and longitude is
+    increasing as you go from upper left to lower right.  The offset
+    is where the origin (latitude=0, longitude=0) is found.
+
+    The position counting down to zero changes the putchar() from
+    printing ('!' or ' ') to printing ('"' or '#').
+
+    The "H E L L O,   W O R L D!" string inside the data string
+    prints the line of blanks past Tierra del Fuego and the last
+    blank line.  It's just for show, really.
+
+    Since the resolution is coarse, a few costal cities are shown to
+    be just off the map; this is an unavoidable artifact.  The map
+    is reasonably accurate.
+
+    Here are some cities you might like to try:
+
+         New York  41  -74       Los Angeles  34 -118
+           London  52    0             Paris  45    2
+           Moscow  56   38           Beijing  40  116
+        New Delhi  29   77    Rio de Janeiro -23  -43
+           Sydney -34  151             Tokyo  36  140
+
+For a domestic (USA) version with higher resolution, try:
+---cut---
+main(l,a,n,d)char**a;{for(d=atoi(a[1])/2*80-atoi(a[2])-2043;
+n="bnaBCOCXdBBHGYdAP[A M E R I C A].AqandkmavX|ELC}BOCd"
+[l++-3];)for(;n-->64;)putchar(!d+++33^l&1);}
+---cut---
+The code will test the 80-column wrap and document itself if it is
+joined together as one 160-character line and listed.  You should see:
+
+main(l,a,n,d)...
+[A M E R I C A]...
+
+...going down the left edge if your terminal autowraps at 80 characters.
+
+Copyright (c) 1992, Landon Curt Noll & Larry Bassel.
+All Rights Reserved.  Permission for personal, educational or non-profit use is
+granted provided this this copyright and notice are included in its entirety
+and remains unaltered.  All other uses must receive prior permission in writing
+from both Landon Curt Noll and Larry Bassel.